Configure these switches to match the communication speed set on the master Intelligent System Controller port. 19200 bps 38400 bps 115200 bps RS-485 Line Termination (Switch 8)
: Switch 8 enables encrypted communication. All other configuration settings are made in the host software.
If a reader fails to power up on the LNL-1320-2RP: lenel lnl3300m5 installation manual upd top
The Intelligent System Controller (ISC) is a specialized physical security hub built exclusively for seamless migration scenarios. Engineered as a direct drop-in replacement for legacy CASI M5 and M3000 enclosure architectures, this hardware board bypasses the need for costly field rewiring. It instantly connects outdated controller cages to modern enterprise security networks managed by the LenelS2 OnGuard platform.
Two onboard inputs are available. They can be configured as unsupervised (normally open/normally closed switches) or supervised using dual EOL (End-of-Line) resistor networks (typically 1K or 4.7K ohm resistors based on software settings). Door Position Switch (Door Contact) IN2 (TB2-3 / TB2-4): Request-to-Exit (REX) Device 5. Relay Outputs (TB3) Configure these switches to match the communication speed
The reader port supports Wiegand or Clock-and-Data signalling structures. Reader Power Out (+5 VDC or +12 VDC pass-through) TB4-2: Data 0 / Data TB4-3: Data 1 / Clock TB4-4: Green LED Output TB4-5: Red LED Output TB4-6: Buzzer/Beeper Output TB4-7: Ground 4. Alarm Inputs (TB2)
Log in using the factory credentials found in your deployment documentation. If a reader fails to power up on
Switches 1 through 5 on block S1 establish the unique hardware address of the controller on your local sub-network. Configure these using binary encoding according to your OnGuard system design schema. S2 Configuration (Baud Rate and Operation)
"Come on," he muttered, swiping through his cached files. He needed the pinouts for the and the specific DIP switch settings for the M5’s high-speed downstream communication. One wrong flip and he’d lock out three floors of security guards.
: Power down the legacy controller, unplug existing field wiring from the legacy CPU, insert the new LNL-3300-M5 , and reconnect the wiring. Compatibility
: For initial web configuration, turn DIP switch 2 ON , while 1, 3, and 4 remain OFF.
Configure these switches to match the communication speed set on the master Intelligent System Controller port. 19200 bps 38400 bps 115200 bps RS-485 Line Termination (Switch 8)
: Switch 8 enables encrypted communication. All other configuration settings are made in the host software.
If a reader fails to power up on the LNL-1320-2RP:
The Intelligent System Controller (ISC) is a specialized physical security hub built exclusively for seamless migration scenarios. Engineered as a direct drop-in replacement for legacy CASI M5 and M3000 enclosure architectures, this hardware board bypasses the need for costly field rewiring. It instantly connects outdated controller cages to modern enterprise security networks managed by the LenelS2 OnGuard platform.
Two onboard inputs are available. They can be configured as unsupervised (normally open/normally closed switches) or supervised using dual EOL (End-of-Line) resistor networks (typically 1K or 4.7K ohm resistors based on software settings). Door Position Switch (Door Contact) IN2 (TB2-3 / TB2-4): Request-to-Exit (REX) Device 5. Relay Outputs (TB3)
The reader port supports Wiegand or Clock-and-Data signalling structures. Reader Power Out (+5 VDC or +12 VDC pass-through) TB4-2: Data 0 / Data TB4-3: Data 1 / Clock TB4-4: Green LED Output TB4-5: Red LED Output TB4-6: Buzzer/Beeper Output TB4-7: Ground 4. Alarm Inputs (TB2)
Log in using the factory credentials found in your deployment documentation.
Switches 1 through 5 on block S1 establish the unique hardware address of the controller on your local sub-network. Configure these using binary encoding according to your OnGuard system design schema. S2 Configuration (Baud Rate and Operation)
"Come on," he muttered, swiping through his cached files. He needed the pinouts for the and the specific DIP switch settings for the M5’s high-speed downstream communication. One wrong flip and he’d lock out three floors of security guards.
: Power down the legacy controller, unplug existing field wiring from the legacy CPU, insert the new LNL-3300-M5 , and reconnect the wiring. Compatibility
: For initial web configuration, turn DIP switch 2 ON , while 1, 3, and 4 remain OFF.